The 16-section written fall protection plan GCs, primes, and specialty subs use to satisfy OSHA 1926 Subpart M. Hazard inventory by trade and area, system selection, anchor-point requirements, PFAS specs, controlled access zones, rescue plan, and amendment cadence in one editable starting point.
Why every construction project above six feet needs a written fall protection plan
Falls are the leading cause of death in construction. Accounting for roughly one-third of all fatalities in the industry every year, according to OSHA’s own fatality data. OSHA 1926 Subpart M has been on the books since 1994, yet falls from elevation remain the single largest contributor to the Fatal Four. The regulation isn’t complicated: protect workers at six feet or above on most construction surfaces, at ten feet on scaffolding, and at any height over dangerous equipment or into dangerous openings. The rules are clear. The execution is where projects fall apart.
Most contractors don’t fail on fall protection because they don’t know the rules. They fail because no one wrote down the plan. A competent safety officer knows the regulations cold, but that knowledge lives in their head, not in a document the foreman can brief on Monday morning, not in a file the OSHA compliance officer can review during a site inspection, not in a version-controlled artifact the project manager can sign and route before the first crew goes over six feet. OSHA 1926.502(k) requires a written fall protection plan for certain operations. Leading edge work, controlled access zones, and any situation where conventional fall protection is infeasible or creates greater hazard. But even where the written plan isn’t strictly mandated for your scope, project owners, federal contracting officers, and GC safety directors increasingly require one before crews mobilize.
What a written fall protection plan actually does for you: it forces the hazard inventory to happen before someone is already at elevation. It documents the system selection. Guardrails where you can install them, PFAS where guardrails aren’t feasible, safety nets where overhead work is happening, controlled access zones for specific leading-edge operations. It names the competent person so everyone on site knows who to call when conditions change. It documents the rescue plan so the question “what do we do if someone gets suspended in their harness” has an answer before the harness gets worn. And it creates the paper trail that matters when OSHA shows up.
This template is the artifact a site safety officer, project manager, or specialty sub keeps on their machine and copies into every new project. It walks through 16 sections that a fall protection plan must address to be functional and defensible, not a compliance checkbox, but a working document a crew can actually use. The 16 sections cover everything from the project’s fall hazard inventory by trade and area, through system selection and anchor-point requirements, through the rescue plan and equipment retirement criteria, through the amendment cadence that keeps the plan current as work evolves.
What this template is NOT: it’s not a substitute for a site-specific competent person evaluation, it’s not legal advice on whether your program satisfies your insurer’s standards, and it’s not a guarantee of acceptance on any specific project or contract. Every project has unique hazards, unique structures, and unique access constraints that a generic template can’t anticipate. What this gives you is the structural floor. The 16 sections a working fall protection plan needs, in the sequence a competent person can work through, so your prep time goes to identifying real hazards and selecting the right systems instead of figuring out what the document is supposed to contain.
Use this before any project where workers will be exposed to fall hazards above six feet. Refresh it when scopes change, when new trades come on, when work moves to new elevations or roof areas, when corrective actions from near-misses require program updates, and at the amendment cadence you specify in Section 16.
Who this fall protection plan template is for
- Mid-market general contractors managing multi-trade projects with multiple elevation hazard zones
- Prime contractors required to submit a fall protection plan before mobilization on owner or GC safety-plan submittals
- Specialty subcontractors, steel erectors, roofing crews, glazing installers, HVAC crews, electrical crews working at elevation, who need a scope-specific written plan
- Site safety officers and
- competent persons drafting the plan and maintaining it through construction
- Project managers routing the plan through signoff before mobilization
- Foremen and crew leads briefing the plan to their crews before work at elevation begins
If you’re on a federal project, your fall protection plan is a section of the broader Site Safety and Health Plan required by EM 385-1-1. Start with the Federal site safety plan (EM 385-1-1) template and use this template to draft Section 7 (fall protection) of that document. For the per-activity breakdown, the Activity hazard analysis (AHA) template carries the fall-specific steps, hazards, and controls down to the crew level.
The 16 sections the fall protection plan covers
The template covers 16 sections every working fall protection plan must address before crews go above six feet:
- Project information, contract reference, and plan scope. Capture the project name, address, contract number, GC name, owner, and plan effective date. State which trades and work areas this plan covers, the anticipated peak workforce at elevation, and the highest elevation crews will work at. OSHA compliance officers and owner safety reviewers use this section to confirm the plan was written for this project, not copied from last year’s job.
- Plan author, preparer credentials, and competent person designation. Name the person who prepared this plan, their title, employer, and the qualification that establishes their competent-person status under OSHA 1926.32(f). Training history, experience documentation, and employer designation letter. Also name the on-site competent person who will administer the plan day-to-day, plus the designated alternate. The competent person must be capable of identifying existing and predictable fall hazards and has authority to take prompt corrective measures. Document that authority here.
- Fall hazards inventory by trade and work area. The heart of the plan. Walk every area of the project where fall hazards exist and list them: unprotected floor openings, leading edges, roof perimeters, excavations, wall openings, skylights, stairwells under construction, structural steel, scaffolding perimeters, aerial work platform outreach zones, and any other elevation exposure. For each hazard, identify the trade(s) exposed, the approximate elevation, the anticipated duration of exposure, and the conventional fall protection method initially selected. This section must be project-specific. Generic hazard lists are the most-cited deficiency in plan reviews.
- Fall protection systems selected per hazard. For each hazard in the inventory (Section 3), state the fall protection system selected and why. The OSHA 1926 Subpart M hierarchy: guardrail systems first (1926.502(b)); safety net systems second (1926.502(c)); personal fall arrest systems third (1926.502(d)). If conventional systems are infeasible or create greater hazard, document that determination here (supported by the competent person evaluation) and identify the alternative. Controlled access zone, safety monitor system, or written plan per 1926.502(k). System selection must be made per hazard, not per project. A single project commonly uses multiple systems in different zones.
- Anchor point requirements and engineering documentation. For every location where personal fall arrest systems will be used, identify the anchor points. Structural members, certified anchor devices, horizontal lifeline systems, or engineered tie-off points. Each anchor must support a minimum 5,000 pounds per attached worker, or be designed by a qualified person with a safety factor of at least two. Document who evaluated each anchor point (competent person or qualified person/PE), the load rating, and the supporting documentation (engineer stamp, manufacturer cert, or competent-person inspection record). Anchor points are where PFAS systems fail. Every anchor must be in the plan before it’s used.
- Personal fall arrest system (PFAS) specifications and equipment standards. Specify the PFAS components authorized for use on this project: harness type and ANSI Z359.11 class, connector type (snap hooks, carabiners. Self-locking, double-locking), lanyard type (self-retracting lifeline, shock-absorbing lanyard, positioning lanyard), and horizontal lifeline systems where used. Document the fall clearance calculation for each application. Total arrest distance must not allow the worker to contact a lower level or obstruction. Equipment must be ANSI-compliant, inspected before each use, and removed from service immediately when damaged.
- Guardrail and safety net specifications. Where guardrail systems are used, specify top rail height (42 inches ±3 inches), mid-rail height (21 inches minimum), toeboard requirements where tools or materials can fall, and load rating (200 lb outward/downward at top rail). Where safety net systems are used, document the net specification (ANSI A10.11), maximum drop distance (30 feet), required border rope strength (5,000 lb minimum), mesh size limit (6-inch maximum), and inspection schedule. Name the qualified person who designed or approved the net installation.
- Leading edge work plan and controlled access zone specifications. If any scope involves leading edge work (structural steel erection, roofing at the deck edge, precast erection) where conventional fall protection is infeasible, document the determination by the competent person, the scope of the leading edge work, and the controlled access zone (CAZ) specifications: CAZ boundary 6 to 25 feet from the unprotected edge, boundary marked with high-visibility rope or equivalent, access restricted to authorized workers only (documented authorization list), and CAZ active only when leading edge work is in progress. Maximum number of workers in the CAZ at any time. CAZ use is conditional. It does not replace guardrails or PFAS where those systems are feasible.
- Safety monitor system (where applicable). If a safety monitor system is used for roofing work on low-slope roofs (per 1926.502(h)), document the scope and conditions: low-slope roof only (pitch ≤4:12), safety monitor is a competent person, safety monitor is on the same surface within visual and verbal contact of every worker being monitored, no mechanical equipment being operated when safety monitor is the only protection, and no worker is assigned other duties while serving as safety monitor. Name the designated safety monitor(s) and their alternates. Safety monitor is the protection method of last resort. Document why alternatives are infeasible if used.
- Training requirements and competent person designation per trade. List the fall protection training required before any worker is exposed to a fall hazard on this project: OSHA 1926.503 training (recognition of fall hazards, procedures for assembly/maintenance/disassembly/inspection of fall protection systems, limits of equipment, correct procedures for erecting/installing/using fall protection systems), equipment-specific training for each PFAS component type in use, and any additional training required by the GC or owner. Document how training records will be retained and who will verify records before elevation exposure.
- Rescue plan and rescue equipment. What happens when someone ends up suspended in their harness? Document the rescue plan: named rescue team or designated rescue personnel (or third-party rescue service), rescue equipment staged on site (rescue ladder, rope rescue system, aerial work platform designated for rescue use, or other approved method), maximum rescue response time (suspension trauma can begin within minutes), and procedure for calling emergency services if rescue cannot be accomplished within the response time. The rescue plan is the most-overlooked section of most fall protection programs. Workers have died from suspension trauma while crews tried to figure out how to get them down.
- Equipment inspection schedule and pre-use inspection procedures. PFAS equipment must be inspected before each use by the user, and at a competent-person level periodically during the project. Document the inspection cadence: pre-use inspection checklist (harness stitching, hardware function, connector gate, lanyard condition, SRL energy indicator, lifeline wear), competent-person periodic inspection schedule (at minimum monthly during active use), inspection record format and location. Equipment that has arrested a fall must be removed from service immediately regardless of visible condition. Document that procedure here and name who makes the removal decision.
- Equipment retirement criteria and removal from service. State the criteria for retiring fall protection equipment: any equipment that has arrested a fall (automatic removal), visible damage (cut webbing, cracked hardware, damaged stitching, deformed connectors), equipment exceeding manufacturer-recommended service life, equipment where SRL energy indicator has deployed, equipment failing pre-use inspection. Document the retirement procedure. Tag, remove from the job-site equipment locker, and either destroy or return to the manufacturer. Equipment marked ‘DO NOT USE’ on a shelf is not retired. Document what actually happens to it.
- Accident and near-miss investigation procedure. Document the procedure for investigating any fall, near-miss, or fall-protection equipment failure on this project: immediate response (secure scene, provide first aid, call emergency services if needed), notification chain (foreman to superintendent to project manager to corporate safety within 24 hours; OSHA 300 log update; OSHA 8-hour reporting threshold for fatalities and hospitalizations), investigation steps (preserve evidence, interview witnesses, photograph conditions), root-cause determination, corrective action assignment, and plan amendment if the investigation reveals a gap in this document. Name the investigation lead.
- Emergency contacts and site-specific emergency procedures. List the emergency contacts active for this project: 911 (primary), nearest hospital and trauma center (address and phone), project site address for 911 dispatch, named OSHA area office and phone, GC safety director, owner safety representative, corporate safety officer, and workers’ compensation carrier’s 24-hour injury hotline. State site-specific evacuation procedures relevant to fall incidents. How workers at elevation are evacuated during a site emergency, where the emergency assembly point is, and how a head count is conducted.
- Plan review, amendment cadence, and subcontractor conformance. Document when this plan will be reviewed and potentially amended: on mobilization of each new trade or subcontractor with elevation exposure, on any scope change that creates a new fall hazard or changes an existing one, after any fall, near-miss, or fall-protection equipment failure, and at the periodic review interval established by the competent person (at minimum every 30 days during active work with elevation exposure). State how subcontractors with elevation exposure are required to conform to this plan or submit their own plan for the competent person’s review and acceptance before mobilizing. Name who approves plan amendments and how amendments are distributed to affected foremen and crew leads.
How to build and maintain a working fall protection plan on every project
Use this template before any project where crews will be exposed to fall hazards above six feet. For each project:
- Open the DOCX version and save a project-specific copy to your safety file. Name it <project-number>-FPP-v01.docx. Walk the site (or study the drawings) before completing Section 3. The hazard inventory must reflect this project’s actual conditions. Generic lists get plans returned for rewrite.
- Complete Section 4 (system selection) for every hazard in your inventory. Assign a system to every hazard before anyone goes over six feet.
- Have the competent person sign. Have the project manager or superintendent sign. Distribute to every foreman with elevation exposure before mobilization.
- Brief the plan at the pre-task safety meeting. Workers can’t follow a plan they haven’t heard.
- Refresh on every trigger event listed in Section 16. Scope changes, new subs, near-misses, accidents. Keep the revision log current.
Stop routing fall protection plans through email
The 16 sections above take a site safety officer 6 to 12 hours to draft on a new project, and then the routing begins: competent person signs, project manager signs, GC safety director signs, owner safety rep reviews, affected foremen receive their copies. That routing happens in email, signatures live in scanned PDFs, revision history fragments across a chain of Reply Alls, and by the time the third amendment is issued nobody can confirm who has the current version. Contracts Connected’s Approval Workflows route fall protection plan drafts through every required signoff automatically, version every amendment, capture electronic signatures, distribute the current version to every named foreman when it changes, and keep the audit-trail file ready for OSHA the moment they walk onto your site.
For educational purposes. These templates, checklists, and trackers are operator-built starting points designed to help you move faster on the kind of work that usually drowns construction admins in email chains. They are not legal, insurance, accounting, or tax advice. Each project, jurisdiction, and contract has its own quirks. Review the document, refine the language, and consult your attorney, broker, CPA, or compliance officer before relying on it for a live project decision.
Fall protection has direct life-safety consequences. This template is a structural starting point, not a substitute for a site-specific competent person evaluation. Review the document with your safety officer or qualified safety professional before deploying on any live project.
Frequently asked questions about fall protection plans
Is a written fall protection plan always required by OSHA?
OSHA 1926.502(k) requires a written fall protection plan specifically for leading edge work, precast concrete erection, and residential construction when conventional fall protection is infeasible or creates greater hazard. For most other construction work above six feet, OSHA 1926 Subpart M requires a fall protection system, but the written plan requirement is specific to those scenarios. That said, most project owners, federal contracting officers, and GC safety programs require a written plan before crews mobilize regardless of OSHA’s written-plan trigger. A written plan is always the professional standard, even when it isn’t strictly mandated for your scope.
What’s the difference between a fall protection plan and an Activity Hazard Analysis?
The fall protection plan is the program-level document: it covers the project’s full fall hazard inventory, system selections, competent person designations, rescue plan, and amendment cadence. The AHA (Activity Hazard Analysis) is the per-activity worksheet: it breaks a specific activity into principal steps, ties hazards to each step, lists controls per step, and captures the crew briefing and acknowledgment signatures. On federal projects (EM 385-1-1), both documents are required. The fall protection plan in the SSHP and an AHA for each activity. On commercial projects, the fall protection plan often functions as the only formal document; on higher-hazard work, adding activity-level AHAs elevates both safety and OSHA defensibility.
What qualifies someone as a competent person for fall protection?
Under OSHA 1926.32(f), a competent person is someone capable of identifying existing and predictable hazards in the surroundings or working conditions that are unsanitary, hazardous, or dangerous to employees, and who has authorization to take prompt corrective measures to eliminate them. For fall protection specifically, this means the person can identify fall hazards, evaluate anchor point adequacy, assess the feasibility of fall protection systems, inspect PFAS equipment, and implement corrective action without waiting for permission. The competent person designation is employer-assigned. There is no OSHA-required certification card. Training history, documented experience, and an explicit employer designation letter are the standard documentation package.
When does controlled access zone use require a written plan?
OSHA 1926.502(k) requires a written fall protection plan any time a controlled access zone (CAZ) is used as the fall protection method. Meaning when guardrails, PFAS, or safety nets are determined by the competent person to be infeasible or to create greater hazard for a specific operation. The plan must document: the determination that conventional fall protection is infeasible, who made that determination, the scope and boundaries of the CAZ, authorization procedures for worker entry, and how the CAZ is enforced. CAZ use without a written plan is an OSHA violation. Section 8 of this template provides the CAZ documentation structure.
How do I handle subcontractors who have their own fall protection plans?
Two acceptable approaches. Approach 1: the sub operates under the GC’s fall protection plan. The sub’s competent person reviews and accepts the GC’s plan, and the sub’s foremen are briefed on it before mobilizing. Approach 2: the sub submits their own fall protection plan, which the GC’s competent person reviews and accepts (or returns for revision) before the sub begins elevation work. In either case, Section 16 of this template documents how sub conformance is managed. The GC retains accountability for fall protection on their project: ‘the sub had their own plan’ is not a defense if the sub’s plan was inadequate and the GC never reviewed it.
What’s suspension trauma and why does it matter for the rescue plan?
Suspension trauma (also called orthostatic shock or harness-induced pathology) occurs when a worker is left suspended in a full-body harness after a fall arrest. Blood pools in the legs, venous return to the heart drops, and the worker can lose consciousness and suffer cardiac arrest within minutes. Some studies suggest serious physiological effects can begin in as little as 3 to 5 minutes of suspension. This means a rescue plan that relies on calling 911 and waiting is not a rescue plan. Section 11 of this template requires a pre-staged, named, capable rescue team or service with a response time fast enough to prevent suspension trauma. Document it, stage the equipment, train the team, and drill it before crews go over six feet.